Robe 250 AT Especificaciones

1 Version 1.2

10For overhead use, always install a safety-rope that can hold at least 10 times the weight of the xture. You must only use safety-ropes with screw-o

114.7 DMX-512 connection/connection between xturesThe xture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets a

125. ColorWash 250 AT-DMX Protocol-version 1.0 Mode/ChannelValue FunctionType of control1 2 3 41 1 1 1 0 - 255PanPan movement by 530°proportional2 2

13 Mode/ChannelValue FunctionType of control1 2 3 47 7 9 901836547290108128-129130-139140-149150-159160-169170-179180-189190-215216-217218-243244-2492

14 Mode/ChannelValue FunctionType of control1 2 3 413 12 15 14184-191192-199200 - 207208 - 215216 - 223224 - 231232 - 239240 - 243244 - 249250 - 255M

156. Controller mode The xtures are individually addressed on a data link and connected to the controller.The xtures respond to the DMX signal from

16Shutter/StrobeExtremely fast shutter is also used for strobe effect (1 - 10 ashes per second)7. Stand - alone modeThe xtures on a data link are n

178.Control menu mapDefault settings=Bold print A001 dM.Ad. 001 : 512 MA.SL. d.AbL MASt. SLA.1

18 En.Sn.(On,Off) dISP. turn (On,Off) d.On (On,Off) d.Int.(20...100) bL.Co.(On,Off) FEEd. (On,Off) MI.SE(1

19 rESE. SPEC. LA.Ad. PAn (0-255) tilt (0-255) CodE rdML rdMH AdJ. Pan (0-255) : F.C

2Table of contents1. Safety instructions ... 32.

209. Control menu The control panel situated on the front panel of the base offers several features. You can simply set the DMX address,read the numbe

21 ColorWash 250 AT has been powered on since the counter was last reset.In order to reset this counter to 0 you have to hold [UP] and[DOWN

229.4 PersonalityUse this menu to to modify ColorWash 250 AT operating behavior.r.PAn --- Pan reverse.Select this function to invert the pan movemen

23Fan.S. --- Fan speed operating modes.By using this function you can choose 2 types of the fan speed op-erating modes. Auto --- The fans automat

249.7 Test sequencesUse this menu to to run a special demo-test sequences without an external controller, which will show you some possibilities of us

25 P.t.SP. a pan/tilt speed Colo. a colour wheel CYAN cyan lamellas MAGE. magenta lemellas YELL. yellow lamelas C.SPd. a CMY/dimmer speed

26Connect the DMX controller to the xture, press [ENTER] and the [UP] and [DOWN] buttons in order to display the following items: "Colo,EFFE,Zoo

27Note:All motors in "Power down mode" are deactivated and switching on the lamp from the control panel is blocked. 11. RDM This xture sup

2812. Error and information messagesHEAtThis message appears if you try to switch on the lamp within 5 minutes after having switched it off (the lamp

29t.M.Er.(Temperature measuring error)The message informs you that the communication betwen the head and the main board in the xture base was cut off

3CAUTION!Keep this device away from rain and moisture!Unplug mains lead before opening the housing!FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL C

30 -Tilt movement range 268° -16 bit movement resolution -Automatic Pan / Tilt position correction -Remotely controllable speed of pan/ti

31Dimensions(mm) 14. Maintenance and cleaningIt is absolutely essential that the xture is kept clean and that dust, dirt and smoke-uid residues mus

32

42.Operating determinationsThis device is a moving-head for creating decorative effects and was designed for indoor use only.If the device has been e

53. Description of the device1 - Moving head2 - Yoke3 - Front lens4 - BaseRear panel of the base:5 - Power switch 6 - Power cord7 - Fuse holder 8 -

64. Installation4.1Fitting the lampDANGER !Install the lamps with the device switched off only.Unplug from mains before !To insert the lamp loosen th

74.2 Lamp adjustment The ColorWash 250 AT lamp holder is aligned at the factory. Due to differences between lamps, ne adjust-ment may improve light p

84.4 Connection to the mainsVerify the power supply settings before applying power!If you wish to change the power supply settings,see the chapter bel

94.6 Rigging the xtureDANGER TO LIFE! Please consider the respective national norms during the installation! The installation must only be carried