Robe Robin 100 LEDBeam Wireless DMX CRMX Especificaciones descargar pdf (Pagina 27)

6.7 Reset

This option enables the Robin 100 LEDBeam to index all effects and return to their standard positions.

6.8 Special functions (Special)

RDM Low - This menu item shows the rst part of the RDM identication code.

RDM High - This menu item shows the second part of the RDM identication code.

Wireless - Wireless DMX information. The menu allows to read some information about

Wireless DMX operation

Stat - Wireless status. Use the menu to read wireless DMX status.

Unlink - use this item to unlink xture from wireless DMX.

Adjust - Adjustment. The menu allows the ne adjustment of effects.

DMX Val- DMX values. Use the menu to set DMX values of xture´s channels.

Calib - calibration of white colour.

Cal P/T - Use this menu to calibrate pan/tilt positio.

Cal Col - Use this menu to set white colour 5600K.

Calibration of the pan/tilt via the control board

1. Disconnect DMX controller from the xture and enter the "Cal P/T" menu.

2. Use the [PREV] and [NEXT] to nd "Pan" and press [ENTER].

3. Set desired value and save it by pressing [ENTER].

4. Repeat steps 2 and 3 for Tilt.

5. After calibrating both effects, nd item "Store" and press [ENTER]. to save all adjusted values and reset the

xture.

Calibration of the white 5600K via the control board

1. Disconnect DMX controller from the xture , open the sShutter and Dimmer and set the Virtual colour wheel

channel at DMX=10 (white 5600K). Aim the light beam on the lux meter (e.g. Minolta CL-200A Chroma meter)

which is placed cca 5m from the xture.

2. Set the menu item Colour Calibration Mode to On (Pers-> C Cal M -> On).

3. Enter the menu "Cal Col".

4. Use the [NEXT] or [PREV] button to select desired colour and press the [ENTER] button.

5. Use the [NEXT] or [PREV] button to set desired value of colour.

5. By means of the "Red C, Grn C, Blue C and Whi C" items adjust the 5600K colour temperature

as exactly as possible (∆u´v´= 0).

7. After adjusting 5600K colour temperature, select item Store and press the [ENTER] button to save all

adjusted values .

Note: you can also use DMX controler for both calibrations stated above, calibration protocol is the following:

Effect Mode 1 Mode 2 Mode 3 Mode 4 Mode 5

Pan-ne adjustment channel 36 channel 20 channel 15 channel 10 channel 36

Tilt - ne adjustment channel 37 channel 21 channel 16 channel 11 channel 37

Red - red saturation channel 38 channel 22 channel 17 channel 12 channel 38

Green- green saturation channel 39 channel 23 channel 18 channel 13 channel 39

Blue - blue saturation channel 40 channel 24 channel 19 channel 14 channel 40

White - white saturation channel 41 channel 25 channel 20 channel 15 channel 41

Cal Load - Loads default (factory) calibration.

Sw Upd - Software update. The menu item allows you to update software in the xture via either serial or

USB port of PC.

The following are required in order to update software:

- PC running Windows 95/98/2000/XP/7 or Linux

- Update software

- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)

- Robe Universal Interface (if you want to use an USB port of PC)

Note 1: Software update should execute a qualied person. If you lack qualication, do not attempt the update

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 37 38

Comentarios a estos manuales

Sin comentarios

Robe Robin 100 LEDBeam Wireless DMX CRMX Especificaciones Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Reflectores Robe Robin 100 LEDBeam Wireless DMX CRMX