Robe Robin MMX Spot Wireless DMX CRMX Especificaciones

Busca en linea o descarga Especificaciones para Reflectores Robe Robin MMX Spot Wireless DMX CRMX. Robe Robin MMX Spot Wireless DMX CRMX Specifications [en] Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir

Indice de contenidos

Pagina 2 - Robin MMX Spot

104.6 Rigging the xtureThe installation of the xture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour withou

Pagina 3 - 1. Safety instructions

11Omega holders positions:Truss installation1.Bolt each clamp (1) to the omega holder (3) with M12 bolt and lock nut through the hole in the holder.2

Pagina 4 - 2. Operating determination

124.7 DMX-512 connectionThe xture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired in parallel.Only

Pagina 5 - 3. Fixture exterior view

134.8 Ethernet connectionThe xtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control soft-ware running on

Pagina 6 - 4.1 Connection to the mains

14Ethernet / DMX operationOptions “Art2DMX” has to be selected from the “Ethernet Mode” menu on the rst xture (connected to the Ethernet) in the xt

Pagina 7 - 4.3 Lamp adjustment

155. Remotely controllable functionsLampThe Robin MMX Spot is to be operated with a Philips MSR Platinum 35.Note: It is also important to note, that t

Pagina 8 - 4.4 Replacing rotating gobos

166. Control menu mapDefault settings=Bold printTab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6Addressing Settings DMX Address 001-255 Ether

Pagina 9 - 4.5 Replacing graphic wheels

17Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6Lamp OnLamp OffFixture PositionFixture Temperatures Head TemperaturesAmbient TemperaturesBase Tem

Pagina 10 - 4.6 Rigging the xture

18Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6Dim./Strobe/H.-Spot Res.Zoom/Foc./Fro./Pri. Res.Iris/Dual G. Wheel ResetPreset Effect Con-tro

Pagina 11 - DANGER TO LIFE!

197. Control menu The Robin MMX Spot is equipped with the QVGA Robe touch screen with battery backup which allows to set the xture´s behaviour acco

Pagina 12 - 4.7 DMX-512 connection

2Table of contents1. Safety instructions ... 32.

Pagina 13 - 4.8 Ethernet connection

20Note: The green icon at the top right corner of the screen indicates the level of the display battery charging. If the whole icon is green, the batt

Pagina 14 - Ω resistor

21 There cannot be 2 xtures with the same IP address on the network! Default IP Address -Preset IP address, you can set up only rst byte o

Pagina 15

22 Base Temperature - The menu shows temperature in the xture base (on the display PCB). Current - A current temperature in the xture base.

Pagina 16 - 6. Control menu map

23 Fixture Position - Recorded installation positions of the xture: Fixture Temperatures - Recorded temperatures which have exceeded dened level

Pagina 17

24Blackout Settings - Use the menu if you need to close the light output under certain conditions which are described below Blackout DMC - Blackout

Pagina 18 - * Wireless version only

25Default Settings - The menu item allows to set all xture parameters to the default (factory) values.7.4 Tab "Manual Control"Reset Functio

Pagina 19 - 7. Control menu

26and [down arrow] and set all desired effects.An item "Step Time" (value of 0-25.5 sec.) is the time during which effects last in the curr

Pagina 20 - 7.1 Tab " Address"

273. Set desired value and save it by touching the [conrm].4. Repeat steps 2 and 3 for the next effects.5. After calibrating all effects, touch the [

Pagina 21

28 3. Run the Software Uploader program. Select desired COM and then click on the Connect button. (Select COM if the serial port is used or DreamBox

Pagina 22

29SUPPORTED_PARAMETERS *SOFTWARE_VERSION_LABEL *DMX_START_ADDRESS * *IDENTIFY_DEVICE * *DEVICE_MODEL_DESCRIPTION *MANUFACTURER_LABEL *DEVICE_LABEL * *

Pagina 23

3CAUTION!Keep this device away from rain and moisture!Unplug mains lead before opening the housing!FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL C

Pagina 24

30-->Wireless State).To unlink the xture from DMX transmitter.The xture can be unlinked from receiver via the menu item “ Unlink Wireless Adapter

Pagina 25

31CTO Lamella Error 1 (CTO Lamella Error 2)The messages will appear after the reset of the CTO ag if the ag is not located in the default position.S

Pagina 26 - 7.6 Tab "Service"

32Location of the fans:

Pagina 27

3311. Technical SpecicationsElectrical Power supply:...electronic auto-ranging Input voltage range:... 100-

Pagina 28

34Prism Rotating 5-facet prism with continuous rotation in both directionsIris Motorized iris for different beam diametersFrost lter Separa

Pagina 29 - 9. Wireless DMX operation

35Wireless DMX/RDM module (only for Wireless DMX version) Compliance with USITT DMX-512 (1986 & 1990) and 512-A Full DMX delity and frame

Pagina 30

36Accessories Omega holder (No.99010420)...2 pcs Gobo-set 16 (No. 15050025) ... 1 pc

Pagina 32 - Location of the fans:

3812. Maintenance and cleaningIt is absolutely essential that the xture is kept clean and that dust, dirt and smoke-uid residues must not build up o

Pagina 33 - 11. Technical Specications

DMX protocol1234Robin MMX Spot - DMX protocol, version 1.7(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_1308134

Pagina 34 - Position 1

42. Operating determinationThis device is a moving head for creating decorative effects and was designed for indoor use only.If the device has been e

Pagina 35

DMX protocol(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_13081343.zip (DSU_RobinMMXSpot_13081343.tar.bz2) or l

Pagina 36 - Photometric charts

DMX protocol(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_13081343.zip (DSU_RobinMMXSpot_13081343.tar.bz2) or l

Pagina 37

DMX protocol(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_13081343.zip (DSU_RobinMMXSpot_13081343.tar.bz2) or l

Pagina 38 - 13. ChangeLog

DMX protocol(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_13081343.zip (DSU_RobinMMXSpot_13081343.tar.bz2) or l

Pagina 39

DMX protocol(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_13081343.zip (DSU_RobinMMXSpot_13081343.tar.bz2) or l

Pagina 40

DMX protocol(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_13081343.zip (DSU_RobinMMXSpot_13081343.tar.bz2) or l

Pagina 41

DMX protocol(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_13081343.zip (DSU_RobinMMXSpot_13081343.tar.bz2) or l

Pagina 42

DMX protocol(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_13081343.zip (DSU_RobinMMXSpot_13081343.tar.bz2) or l

Pagina 43

DMX protocol(For fixtures produced after 25/08/2013 or updated with a software DSU_RobinMMXSpot_13081343.zip (DSU_RobinMMXSpot_13081343.tar.bz2) or l

Pagina 45

53. Fixture exterior view Rear panel of the base:1 - DMX output (3-pin XLR)2 - DMX output (5-pin XLR) 3 - Ethernet input (RJ45) 4 - Power switch 5 -

Pagina 46

64. Installation Fixtures must be installed by a Qualied electrician in accordance with all national and local electrical and const

Pagina 47

74.2 Installing the lamp DANGER ! Install the lamp with the device switched off only. Unplug from mains before !To insert the new lamp.1. Disconnec

Pagina 48

84.4 Replacing rotating gobos Install gobos with the device switched off only.Unplug from mains before!To replace rotating gobos.1. Disconnect the x

Pagina 49

94.5 Replacing graphic wheels Install graphic wheels with the device switched off only.Unplug from mains before!The dual graphic wheel consists of t

Comentarios a estos manuales

Sin comentarios